HiModel
FLYINGROBOT-400 FIBERGLASS & ALUMINUM 4-AXIAL DIY FRAME
| Wing Span | 18.1 in / 460 mm |
| Wheelbase | 15.7 in / 400 mm |
| Net weight | 0.39 Ib / 170g |
| Flying Weight | 1.47 Ib / 700g |
, , , , , , Specifications:, , , , , , , , , , , FLYINGROBOT-400 COPTER, Specifications:, , ,
Includes/Requires: Includes: 1 x FLYINGROBOT-400 COPTER kit (no electronic accessories) ...HiModel
LOTUSRC T80 QUADCOPTER ARTF
, , , , , , Specifications:, , , , , , , , , , , Technical parameter, , *this sheet is only for reference, product configuration may have little alteration in different versions. Please subject to material object., Efficient payload, , Mini vidicon / camera, , ≤50grams, , , standard, , Maximum lift force, , Use850mAh standard battery, , 380grams, , _, , Maximum payload, , Use 850mAh standard battery, , ≤80grams, , , _, , Maximum takeoff weight, , Use850mAh standard battery, , 280grams, , Safety margin, , Flight distance, , Depend on remote control equipment and battery capacity, , _, , _, , Flight time, , 2S850mAh 15C battery, , 12mins, , Hovering while no wind, , Wind resistance, , ≤4, , class, , _, , Aircraft size, , , 298x298x243, , mm, , ±3mm, , , Maximum expandable size, , 475x475x128, , mm, , ±3mm, , , Motor to motor, , Diagonal distance between two motor centers, , Mm, , ±3mm, , , Battery, , liPo 2S 850MaH 15c, , Standard, configuration, , 1300mAh is usable, , Unit ARF weight, , No battery, receiver, applicable load, , 165grams, , ±5grams, , , Takeoff weight, , 2S 850mAh battery, receiver, , 230grams, , Standard configuration, , , ,
Features: Function and features T80 quad-copter is a mini-type aircraft ...1 Reviews
HiModel
HL W48-30 370KV OUTRUNNER BRUSHLESS DISK TYPE MOTOR FOR QUADCOPTER/MULTI-ROTOR AIRCRAFT
| Model | W4830-370kv |
| Net weight | 154g |
| Max cell number supported | 6S Lipo |
| Max current | 26A |
| Max power | 580W |
| Internal resistance | 0.086Ω |
| Idol current | 1A @ 7.4V |
, , , , , , Specifications:, , , , , , , , , , , Working current: , , ,
Features: - HL disk type motors specially designed for multi-rotor ...HiModel
7 INCH FIBERGLASS PROPELLER PROTECTION RING FOR X330 MINI QUADCOPTER
Specifications:, ,
Features: Includes/Requires:HiModel
ALIEN QUAD'S MULTIROTOR FPV FLYMAN FRAME KIT W/ GOPRO GIMBAL
Specifications:, ,
Features: Includes/Requires:13 Reviews
HiModel
DEBUGGING/ TEST FRAME HOLDER FOR GIMBAL DEBUGGING/TUNNING
Specifications:, ,
Features: Includes/Requires:HiModel
CONVERSION MOUNTING PLATE FOR TAROT GIMBAL TO DJI PHANTOM QUADCOPTER
Specifications:, ,
Features: Includes/Requires:HiModel
SPEED CONTROLLER ASSEMBLY FOR LOTUSRC T580/T580P+ (NEW PROTOCOL)
, , , , , , Specifications:, , , , , , , , , , , Speed Controller Assembly for LOTUSRC T580/T580P+ Quadcopter - new protocol, *There is a white ellipse sticker on the board for the new version, written "new protocol" in Chinese., THERE ARE TWO VERSIONS FLIGHT CONTROL AND ESC AVAILABLE NOW ON THE MARKET, ONE VERSION WITH OLD PROTOCOL, AND ANOTHER WITH NEW PROTOCOL, THE ITEM OF DIFFERENT PROTOCOLS ARE NOT COMPATIBLE, SO PLEASE MAKE SURE THE VERSION YOU ARE USING TO AVOID PROBLEM., , ,
Features: Speed Controller PCB Board for LOTUSRC T580/T580P+ Quadcopters. *This ...HiModel
SPEED CONTROLLER ASSEMBLY FOR LOTUSRC T580/T580P+ (OLD PROTOCOL)
, , , , , , Specifications:, , , , , , , , , , , Speed Controller Assembly for LOTUSRC T580/T580P+ Quadcopter, *There is a white ellipse sticker on the board for the new version, written "old protocol" in Chinese., THERE ARE TWO VERSIONS FLIGHT CONTROL AND ESC AVAILABLE NOW ON THE MARKET, ONE VERSION WITH OLD PROTOCOL, AND ANOTHER WITH NEW PROTOCOL, THE ITEM OF DIFFERENT PROTOCOLS ARE NOT COMPATIBLE, SO PLEASE MAKE SURE THE VERSION YOU ARE USING TO AVOID PROBLEM., , ,
Features: Speed Controller PCB Board for LOTUSRC T580/T580P+ Quadcopters. *This ...HiModel
FRSKY 2.4G 6-CHANNEL TWO WAY COMMUNICATION RECEIVER D6FR
| Compatible with FrSky two way telemetry modules | DFT, DJT, DHT, DHT-U |
| Dimension | 42*22*11mm |
| Weight | 7.1g |
| Operating Voltage Range | 4.0V-10.0V |
| Operating Current | 50mA |
| Specified Range | 1.5km |
| Resolution | 3072 (>11bit) |
| Frame Rate | 18ms (FS) |
| Please kindly follow the steps below to perform range check | (Note |
, , , , , , Specifications:, , , , , , , , , , , 1.1 Compatibility:, 1.2 Specification:, 9ms (HS), Setup, 2.1 Bind procedure:, 1) Turn your transmitter on and switch it to PPM mode (if not set). Turn your transmitter off., 2)Turn your transmitter on while holding the F/S button on the transmitter module (Please make sure that both switches on the transmitter module are OFF in two way mode) Release it in a few seconds. The RED LED on the transmitter module will flash, indicating the transmitter is ready to bind to the receiver., 3) Connect battery to the receiver while holding the F/S button on the receiver. The LED on the receiver will flash, indicating the binding process is completed., 4) Turn on the transmitter and connect battery to the receiver. The Green LED on the receiver will indicate the receiver is receiving commands from the transmitter., 2.2 Range check:, It is highly suggested to perform pre-flight range check. Caution must be paid when you perform range check in environment with metal fences, concrete buildings, or rows of trees. Loss of signal may be experienced from reflections., 1) Place the model at least two feet (60cm) above non-metal contaminated ground (like wooden bench)., 2) Place the receiver’s antennas apart. Do not let the antennas touch the ground., 3) Place the antenna of the transmitter in a vertical position., 4) Turn on the transmitter and receiver, press the F/S button of the transmitter for 4 seconds to enter range check mode, the RED LED of the transmitter module will be off, GREEN LED will flash rapidly, the BEEPER will sound. The effective distance will be decreased to 1/30 of full range., 5) Walk away from the model whi,
Features: Features: 1) Lighter in weight and smaller in dimension. ...HiModel
FY-91Q MULTI-ROTOR FLIGHT STABILIZATION & AUTOPILOT SYSTEM
, , , , , , Specifications:, , , , , , , , , , , FY-91Q Module, Operating voltage ：4.0~6.0 Volt, Current consumption ：50mA (5V input), Dimensions ：55 x 33 x 20 mm, Weight (not including wires) ：20g, Operating Temperature ：-25°C~ +70°C, The maximum allowable rotation rate ： 3 rotations per minute, APPLICABLE AIRCRAFTMODELS, The FY91Q can be installed and flown it the following multi-rotor aircraft:, - 4 motored quadcopters;, - Tri-axial rotory aircraft with 6 motors, - Six-axial multi-rotor aircraft (6 motors), REMOTE CONTROL SYSTEM COMPATIBILITY, FY-91Q have been tested to work with the following RC systems:, · Robbe-Futaba PPM / PCM 1024 / PCM G3 mode, 2.4 GHz systems；, · Graupner/JR PPM 8, PPM 12, SPCM mode；, · MPX PPM8, PPM 12 with UNI mode, · Any remote control system using the standard of 1.5 ms neutral position., , ,
Features: THIS IS FY91Q MODULE ONLY, THE GPS & COMPASS ...HiModel
FPV 720X 480 HIGH DEFINITION CMOS CAMERA CM210 PAL (14G ONLY)
| Sensor | CMOS |
| Resolution | 720x480 200 Million pixel |
| Power Input | 7-12V |
| Video resistance | 75Ω |
| Lens angle | 90 degree |
| Minimum illuminance | 2 LUX/F1.2 |
| Video frame number | 25 frames, PAL |
, , , , , , Specifications:, , , , , , , , , , , Audio: No, , ,
Features: This camera is specially designed to use with Pan ...2 Reviews
HiModel
EAGLE MULTICOPTER FLIGHT CONTROLLER X6 (SUPPORT UP TO 6 ROTORS)
| Input Voltage | 5 ~ 6V DC ( Provided by BEC of ESC ) |
| Output PWM Range | 1520 ± 400μs |
| Frame Rate of PWM Output | 333Hz/ESC, 66Hz/Servo |
| Full-Scale Range of Gyro | ±2000dps |
| Full-Scale Range of Accelerometer | ±4g |
| Operating Temperature | -40 ℃ ~ 85 ℃ |
| Dimensions | 50mm × 50mm |
| Weight | 12g |
, , , , , , Specifications:, , , , , , , , , , , , ,
Features: - Integrated design of 6-axis (3 Gyro+3 Acc ) ...1 Reviews